Dial-Up Error Codes

2 - The system cannot find the file specified.
Error 2.

Reinstall NCP & DUN.


5 - Access Denied.
Error 5.

1. Make sure the username and password are correct with nothing in the " "domain field for NT/2k unless the user should have something there.

2. Make sure " "accept any authentication including clear text is dotted.


5 - Invalid Procedure Call.
Error 5.

Reinstall all Dialup and Network components.


6 - Stack overflow.
Error 6.

1. This is a memory issue try rebooting the computer. A cold boot might be good in this instance.

2. If a reboot doesn't resolve it this could be a RAM or Swap file issue.


20 - The system cannot find the device specified.
Error 20

1. Make sure the correct modem is selected.

2. Does the modem respond to diagnostics? It may need to be reinstalled.

3. Is RNAAPP loaded into memory after closing the dialer? If so try the RNAAPP fix.

4. Reinstall NCP/DUN/RAS.


71 - No more connections allowed.
Error 71[/b:0aebc6c4d6]

1. Is someone connected as you? Been giving out your password?

2. Were you disconnected all of a sudden before this happens? You could be 'ghosted' on the server. The ISP can usually " "bump the 'ghost' off through radius.


380 - Invalid Property Value.
Error 380

1. Make sure autodial is pointing to the correct dialer.

2. Recreate the dialer.


600 - An operation is pending.
Error 600

1. Reboot.

2. Make sure that there are no other dialers fax software or any other programs that use your modem running.

3. Press Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.


601 - The port handle is invalid.
Error 601

1. Press the " "More Info.. button under Diagnostics while the modem's COM port is selected. If you get Ati# responses then you may just have to reboot take out a bum init string or type ATZ as the init.

2. If this does not work or is not the case try reinstalling the modem.

3. Press Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

4. Doesn't look like the modem is working. Refer to computer manufacturer.


602 - The port is already open.
Error 602

1. Reboot.

2. Uninstall and Reinstall the modem.

3. Make sure that no other programs are using your modem. Fax software Supervoice etc...

4. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.


603 - Caller's buffer is too small.
Error 603

1. In the modem properties make sure that the port speed is not set too low.

2. Open up the " "Port Settings and make sure that FIFO's are on and not set too low. Try playing around with these settings until the error goes away.

3. Try uninstalling and reinstalling the modem.

4. Try uninstalling and reinstalling Dialup Networking and all its associated components.

5. Refer to computer manufacturer.


604 - Wrong information specified.
Error 604

1. Retype username and password.

2. Delete and remake the dialer.


605 - Cannot set port information.
Error 605

1. Delete and recreate the dialer.

2. Uninstall and reinstall the modem.

3. Uninstall and reinstall Dialup Networking and all of its associated components.

4. Refer to manufacturer.


606 - The port is not connected.
Error 606

1. Press the " "More Info.. button under Diagnostics while the modem's COM port is selected. If you get Ati# responses then you may just have to reboot take out a bum init string or type ATZ as the init.

2. If this does not work or is not the case try reinstalling the modem.

3. Press Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

4. Doesn't look like the modem is working. Refer to computer manufacturer.


607 - The event is invalid.
Error 607

1. This error should not occur when dialing up to the internet. However if it does take a look at the event log to see if you can figure out what happened.

2. Reboot and check all of the settings for the dialer/network.

3. Reinstall RAS/DUN.


608 - The device does not exist.
Error 608

1. Make sure that the correct modem is selected in the dialer.

2. Make sure (by looking at the modem diagnostics) that the correct modem drivers are being used. If not find and install the correct drivers.

3. Uninstall and reinstall the dialer.

4. If this does not work or is not the case try reinstalling the modem.

5. If the modem responds to diagnostics and responds to ATZ in HyperTerminal try uninstalling and reinstalling Dialup Networking.

6. Doesn't look like the modem is working. Refer to computer manufacturer


609 - The device type does not exist.
Error 609

1. Make sure that the correct modem is selected in the dialer.

2. Make sure (by looking at the modem diagnostics) that the correct modem drivers are being used. If not find and install the correct drivers.

3. Uninstall and reinstall the dialer.

4. If this does not work or is not the case try reinstalling the modem.

5. If the modem responds to diagnostics and responds to ATZ in HyperTerminal try uninstalling and reinstalling Dialup Networking.

6. Doesn't look like the modem is working. Refer to computer manufacturer.


610 - The buffer is invalid.
Error 610

1. In the modem properties make sure that the port speed is not set too low.

2. Open up the " "Port Settings and make sure that FIFO's are on and not set too low. Try playing around with these settings until the error goes away.

3. Try uninstalling and reinstalling the modem.

4. Try uninstalling and reinstalling DUN/RAS and all its associated components.

5. Refer to computer manufacturer.


611 - The route is not available.
Error 611

1. Reboot.

2. Make sure that the dialer and network control panel configurations are valid.

3. Rip and reinstall the network components (unless the user is on a LAN then have them talk to the sysadmin).

4. Refer to manufacturer/sysadmin.


612 - The route is not allocated.
Error 612

1. Reboot.

2. Make sure that the dialer and network control panel configurations are valid.

3. Rip and reinstall the network components (unless the user is on a LAN then have them talk to the sysadmin).

4. Refer to manufacturer/sysadmin.


613 - Invalid compression specified.
Error 613

1. Reboot.

2. Try adding &K3 to the extra settings if this doesn't work try adding &K0.

3. Try reinstalling the modem.

4. Refer to manufacturer.


614 - Out of buffers.
Error 614

1. In the modem properties make sure that the port speed is not set too low.

2. Open up the " "Port Settings and make sure that FIFO's are on and not set too low. Try playing around with these settings until the error goes away.

3. Try uninstalling and reinstalling the modem.

4. Try uninstalling and reinstalling Dialup Networking and all its associated components.

5. Refer to computer manufacturer.

More information on error 614 can be found at:
:whttp://support.microsoft.com/support/kb/articles/q123/5/97.asp


615 - The port was not found.
Error 615

1. Press the " "More Info.. button under Diagnostics while the modem's COM port is selected. If you get Ati# responses then you may just have to reboot take out a bum init string or type ATZ as the init.

2. If this does not work or is not the case try reinstalling the modem.

3. Press Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

4. Doesn't look like the modem is working. Refer to computer manufacturer


616 - An asynchronous request is pending.
Error 616

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


617 - The port or device is already disconnecting.
Error 617

1. Wait for the modem to disconnect.

2. If it is taking too long close RAS.

3. Still not working? Reboot the computer and it should work.


618 - The port is not open.
Error 618

1. Reboot.

2. Make sure that no other programs are using your modem. Fax software Supervoice etc...

3. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.


619 - The port is disconnected.
Error 619

1. Reboot.

2. Make sure that no other programs are using your modem. Fax software Supervoice etc...

3. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.


620 - There are no endpoints.
Error 620

1. Check dialer settings.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out. This is most likely a NetBIOS error.


621 - Cannot open the phone book file.
Error 621

1. Recreate connectoid.

2. Uninstall and reinstall DUN/RAS 1.


622 - Cannot load the phone book file
Error 622

1. Recreate connectoid.

2. Uninstall and reinstall DUN/RAS.


623 - Cannot find the phone book entry.
Error 623

1. Delete and recreate connectoid (more like just a create in most cases because there probably isn't a connectoid).


624 - Cannot write the phone book file.
Error 624

1. Make sure that RASPHONE.PBK is located in system32\\RAS\\. If so rename the file and run RASPHONE.EXE. If not then run RASPHONE.EXE.

2. Uninstall and reinstall DUN/RAS.


625 Fix Invalid information found in the phone book
Error 625

1. Recreate the dialer.

2. Make sure that RASPHONE.PBK is located in system32\\RAS\\. If so rename the file and run RASPHONE.EXE. If not then run RASPHONE.EXE.

3. Uninstall and reinstall DUN/RAS.


626 - Cannot load a string.
Error 626

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


627 - Cannot find key.
Error 627

1. Recreate connectoid.

2. Uninstall and reinstall DUN.


628 - The port was disconnected.
Error 628

1. Make a run through and check all of the dialup/network settings.

2. This is most likely a modem/line noise issue. Check for modem driver updates and try init strings from this page.

3. Check into line noise.


629 - The port was disconnected by the remote machine.
Error 629

1. Does it ask for the UN/PASS more than once? if so verify UN/PASS.

2. Check the dialer settings if ipx/spx is checked and not tcp/ip this would be the cause. In any case the only two things that should be checked are Enable Software Compression and TCP/IP. Also enable DNS. Logon to Network being checked can very well be the culprit.

3. Make sure that the Microsoft VPN Adapter is not selected under connect using.

4. Recreate the dialer.

5. Windows NT? In the Security Tab in Phonebook make sure that " "accept any authentication including clear text is checked.

6. Check the Network Control Panel settings.

7. Reboot the machine.

8. Modem issue? Use this page for driver updates/init strings..

9. Try disconnecting any phones caller ID boxes answering machines line splitters from line. Plug modem directly into the line. Try using a different phone cord between modem and phone socket. Check for line noise.

More info on Error 629 can be found here:
http://support.microsoft.com/support/kb/articles/q190/5/54.asp


630 - The port was disconnected due to hardware failure.
Error 630

1. Is it a Laptop? Try Plugging the PCMCIA Card into a different slot.

2. Is correct modem selected in the connectoid? Select the correct modem.

3. Try rebooting the computer.

4. Does the modem respond to diagnostics? If not uninstall and reinstall it.

5. If so by looking at the Ati's does it look like the correct modem is setup?

6. Try uninstalling and reinstalling the modem anyways.

7. Try an init string. Lower the fifo buffers. Is it a NON-winmodem? If so check required to connect under error control.

8. Update the modem drivers. Try init strings.

9. Check into line noise.

10. Refer to manufacturer.

More info on error 630 can be found at:

http://www.deja.com/[ST_rn=qs]/qs.xp?QRY=microsoft+error+630&OP=dnquery.xp&ST=QS&DBS=2

and at:

http://support.microsoft.com/support/kb/articles/q190/5/54.asp


631 - The port was disconnected by the user.
Error 631

1. Make sure the user is dialing the correct number. Do they need to dial the area code or a dial prefix? Are they disabling call waiting but do not have call waiting?

2. Most likely they just disconnected themselves. Tell them not to cancel the dialing? Reboot the machine.


632 - The structure size is incorrect.
Error 632

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


633 - The port is already in use or is not configured for
Error 633

1. Click Start goto find and click files or folders.

2. Search for telephon.ini.

3. If you find it then rename it to telephon.old or telephon.bad.

4. Click on Start Run then type tapiini.exe press Enter.

5. Reboot.

6. It is also possible that the modem is not setup correctly. Check the modem and possibly Uninstall and reinstall it.

7. Try uninstalling and reinstalling the Dial Up Adapter.

8. Make sure that no other programs are using your modem. Fax software Supervoice etc...

9. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

More info on error 633 can be found at:

http://www.deja.com/[ST_rn=qs]/qs.xp?QRY=microsoft+error+633&OP=dnquery.xp&ST=QS&DBS=2


634 - Cannot register your computer on the remote network.
Error 634

1. Your computer name was unable to register on the network. If you are not on a network check your network settings perhaps change your computer name. Reinstall the network control panel.

2. You are on a network? Contact your network administrator.


635 - Unknown error.
Error 635

1. This is an unknown error. There are several different causes for this error. Just check all their settings and make sure they are correct. Check the connectoid network and see if they have a problem modem or not.

2. If it is a modem with known issues try updating the drivers/init strings.

3. Reinstall DUN/RAS and all associated components.

4. Check into line noise.


636 - The wrong device is attached to the port.
Error 636

1. The wrong modem is selected in the dialer. Select the correct modem.

2. If this is not the case try reinstalling the modem.


637 - The string could not be converted.
Error 637

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


638 - The request has timed out.
Error 638

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


639 - No asynchronous net available.
Error 639

1. Check dialer settings.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out. This is most likely a NetBIOS error.


640 - A NetBIOS error has occurred.
Error 640

1. Check dialer settings.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out.


641 - The server cannot allocate NetBIOS resources needed
Error 641

1. Check dialer settings.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out.


642 - One of your NetBIOS names is already registered on t
Error 642

1. Check dialer settings.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out and to check into another computer using the same computer name on the network.

4. If the user is the LAN/sysadmin then try changing the computer name


643 - A network adapter at the server failed.
Error 643

1. Check dialer settings and make sure they are dialing the correct number.

2. Is the user on a network? If not check the network control panel and perhaps reinstall the components.

3. If the user is on a network have them contact their sysadmin and make sure that their network is configured to dial out.


644 - You will not receive network message popups.
Error 644

1. Check dialer settings. Make sure the correct number is being dialed.

2. If you are not on a network then check your network settings.

3. If you are on a network contact your sysadmin. Someone else on the network is using your messaging name and you will not receive message popups.


645 - Internal authentication error.
Error 645

1. Check the connectoid is require encrypted password checked under the Server Types tab? Uncheck it.

2. Uninstall and reinstall the Dial Up adapter.

3. Recreate the Dialer.

4. Check for extra winsock.dll's and wsock32.dll's.

5. Is VPN installed? If they do not use it get rid of it.

6. Try inits.

7. Uninstall and reinstall network.

8. Nuke the pwl files.

9. Try resetting their password on the server side.

10. Full internet Uninstall and reinstall. (DUN connectoid pwl files and network)

11. Is it a laptop? Try moving the PCMCIA card to another slot.

More info on error 645 can be found here.




646 - The account is not permitted to log on at this time
Error 646

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login at that time of day. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password.


647 - The account is disabled.
Error 647

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password.


648 - The password has expired
Error 648

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password.


649 - The account does not have Remote Access permission.
Error 649

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password.


651 - Your modem (or other connecting device) has reported
Error 651

1. If the modem is not dialing and trying to establish a connection then check to make sure that the modem is installed properly and responds to diagnostics.

1a) Make sure that no other programs are using your modem. Fax software Supervoice etc...

1b) Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

2. If the modem is dialing and trying to establish a connection then try modem driver updates/init strings after checking all of the user's settings.

3. Do a full internet (DUN Network dialers pwl's etc..) uninstall and reinstall.

4. Check into line noise.


652 - Unrecognized response from the device.
Error 652

1. If the modem is not dialing and trying to establish a connection then check to make sure that the modem is installed properly and responds to diagnostics.

1a) Uninstall and reinstall the modem.

1b) Make sure that no other programs are using your modem. Fax software Supervoice etc...

1c) Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

2. If the modem is dialing and trying to establish a connection then try modem driver updates/init strings after checking all of the user's settings.

2a) Make sure that no other programs are using your modem. Fax software Supervoice etc...

2b) Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

3. Do a full internet (DUN Network dialers pwl's etc..) uninstall and reinstall.

4. Check into line noise.


653 - A macro required by the device was not found in the
Error 653

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


654 - A command or response in the device .INF file sectio
Error 654

1. Make sure that no unneeded scripts are being used.

2. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

3. Reinstall RAS/DUN.


655 - The <message> macro was not found in the device
Error 655

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


656 - The <defaultoff> macro in the device .INF file s
Error 656

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


657 - The device .INF file could not be opened.
Error 657

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


658 - The device name in the device .INF or media .INI fil
Error 658

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


659 - The media .INI file refers to an unknown device name
Error 659

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


660 - The device .INF file contains no responses for the c
Error 660

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


661 - The device .INF file is missing a command.
Error 661

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


662 - Attempted to set a macro not listed in device .INF f
Error 662

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


663 - The media .INI file refers to an unknown device type
Error 663

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


664 - Cannot allocate memory.
Error 664

1. System resources have run out. Try a reboot.

2. Make sure that the computer has enough RAM to run windows. If so check the system resources are the still high? If they are then try a full uninstall and reinstall of DUN/RAS. If they are low then have user look into a RAM upgrade or getting rid of some of the startup items.


665 - The port is not configured for Remote Access.
Error 665

1. Reboot.

2. Make sure that no other programs are using your modem. Fax software Supervoice etc...

3. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.


666 - Your modem (or connecting device) isnt functioning
Error 666

1. Check to make sure the correct modem is selected in the dialer.

2. Make sure there are not multiple modems installed.

3. Uninstall and reinstall the modem.

4. Make sure that no other programs are using your modem. Fax software Supervoice etc...

5. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

6. Send to manufacturer?

More info on error 666 can be found at:
http://help.mindspring.com/modules/01400/01401.htm


667 - Cannot read the media .INI file.
Error 667

1. Uninstall and reinstall Network connectoid and DUN.

2. Check for multiple copies of iexplore.exe rename any extra copies that you find.

3. Make sure the correct modem is selected in the dialer.

4. Reinstall the modem.

5. Send to manufacturer.


668 - The connection dropped
Error 668

1. Make sure they are typing in the username and password correctly.

2. Make sure dialer and network control panel settings are correct.

3. Recreate dialer.

4. Update modem drivers try inits and commas etc... (use this page!)


669 - The usage parameter in the media .INI file is invalid
Error 669

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


670 - Cannot read the section name from the media .INI file
Error 670

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN


671 - Cannot read the device type from the media .INI file
Error 671

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN


672 - Cannot read the device name from the media .INI file
Error 672

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


673 - Cannot read the usage from the media .INI file.
Error 673

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


674 - Cannot read the max. connection BPS rate from the..
Error 674

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


675 - Cannot read the max. carrier BPS rate from the media..
Error 675

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Reinstall RAS/DUN.


676 - The line is busy
Error 676

1. Make sure the number they are dialing into is correct. Check dial prefixes long distance etc.

2. If they get a modem tone it may be a modem issue. Check for updated drivers and try inits.

3. Try the number is it busy? Is there a POP problem?

4. Is RNAAPP getting stuck? If so refer to the RNAAPP! help page.


677 - A person answered instead of a modem.
Error 677

1. Make sure that they are dialing the correct number. This includes if they should or shouldn't dial the area code a 9 etc...

2. Are they hearing a voice? Not hearing a modem tone? Make sure that the POP isn't having any sort of issues.

3. If they hear a connection sound try R&Ring the modem updating drivers inits ATZX0(reset and blind dial) as an init etc...


678 - There is no answer.
Error 678

1. Is there a handshake? If not the phone number is probably wrong in some way. Are they trying to turn off call waiting the wrong way for their telco? Do they have call waiting? Do they have pulse but are trying to dial tone? Etc...

2. If there is a handshake check their connectoid and network settings. If all looks good it is probably a handshake error. Make sure the correct modem is selected and setup.

3. Try upgrading the firmware. To get them on the net in the meantime try lowering the fifo buffers setting the max speed to 57600 and adding an init string. Try an init that will retain v90 first but if they just want to get on and download their drivers try setting v34. Uninstalling and reinstalling the modem can sometimes help as well.


679 - Cannot detect carrier.
Error 679

1. Make sure that they are dialing the correct number. This includes if they should or shouldn't dial the area code a 9 etc...

2. If they hear a modem tone then try driver upgrades inits add &C0 (carrier detect always on) etc...

3. Make sure that no other programs are using your modem. Fax software Supervoice etc...

4. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

5. Check into line noise. Perhaps do a full internet uninstall and reinstall first to make sure you eliminate any errors that might be on their machine.


680 - There is no dial tone.
Error 680

1. Make sure that the modem is installed and the phone line is running to the modem correctly.

2. Is the dialer pointing to the correct modem?

3. Make sure that no other programs are using your modem. Fax software Supervoice etc...

4. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

5. Try uninstalling and reinstalling the modem. Make sure that they can hear a dialtone through the modem (with a handset). Could be a modem problem. If they don't hear a dialtone it could also be a line jack or general telco problem.

More info on error 680 can be found at:

http://php.iupui.edu/~aamjohns/trouble.html#No Dial Tone


681 - General error reported by device.
Error 681

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Try driver upgrades/inits. Check into line noise.

4. Refer to manufacturer. Most likely a modem issue of some sort.


682 - ERROR WRITING SECTIONNAME
ERROR 682

ERROR WRITING SECTIONNAME ::
NO Fix


683 - ERROR WRITING DEVICETYPE
ERROR 683
ERROR WRITING DEVICETYPE ::

NO FIX


684 - ERROR WRITING DEVICENAME
ERROR 684
ERROR WRITING DEVICENAME ::

NO FIX


685 - ERROR WRITING MAXCONNECTBPS
Error 685

1. Uncheck the " "Connect only at this speed box under the port speed box and set the port speed to 38400 if they have a 33.6 or lower and 57600 if they have a 56k modem.

2. Try a reboot

3. Uninstall and reinstall the modem


686 - ERROR WRITING MAXCARRIERBPS
ERROR 686
ERROR WRITING MAXCARRIERBPS ::

NO FIX


687 - ERROR WRITING USAGE
ERROR 687
ERROR WRITING USAGE ::
NO FIX


688 - ERROR WRITING DEFAULTOFF
ERROR 688
ERROR WRITING DEFAULTOFF ::

NO FIX


689 - ERROR READING DEFAULTOFF
ERROR 689
ERROR READING DEFAULTOFF ::

NO FIX


690 - ERROR EMPTY INI FILE
Error 690

1. Make sure the correct modem is selected in the dialer.

2. Reinstall the modem.

3. Full uninstall and reinstall of DUN/RAS and its associated components.

4. Refer to manufacturer. Most likely a modem software issue.


691 - Access denied because username and/or password is ...
Error 691

1. Verify the UN and PASS is correct. Correct case correct spacing just plain correct and correct realms if the site requires realms authentication.

2. Make sure that they are supposed to be using realms auth and are using/not using it correctly.

3. If this is Windows NT make sure that nothing is typed in the DOMAIN field of the username/password/domain box.

4. Make sure that logon to network is not checked in the connectoid properties.

5. Reboot the computer and try again.

6. Delete all of the pwl files and reboot.

More info on error 691 can be found at:

http://members.tripod.com/paltech/error691.html


692 - Hardware failure in port or attached device.
Error 692

1. Check to make sure the correct modem is selected in the dialer.

2. Make sure there are not multiple modems installed.

3. Uninstall and reinstall the modem.

4. Make sure that no other programs are using your modem. Fax software Supervoice etc...

5. Ctrl-Alt-Delete if you see RNAAPP loaded then go to the RNAAPP fix page.

6. Send to manufacturer?


693 - ERROR NOT BINARY MACRO
Error 693

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Make sure that the files PAD.INF MODEM.INF and SWITCH.INF in C:\\SYSTEM32\\RAS are not marked as read-only and the currently logged on user does have write permissions.

3. Reinstall RAS/DUN.


694 - ERROR DCB NOT FOUND
ERROR 694
ERROR DCB NOT FOUND ::

NO FIX


695 - ERROR STATE MACHINES NOT STARTED
Error 695

1. Uninstall and reinstall dialer network and DUN.

2. Send to manufacturer


696 - ERROR STATE MACHINES ALREADY STARTED
ERROR 696
ERROR STATE MACHINES ALREADY STARTED ::

NO FIX


697 - ERROR PARTIAL RESPONSE LOOPING
Error 697

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


698 - A response keyname in the device .INF file is not in
Error 698

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Make sure that the files PAD.INF MODEM.INF and SWITCH.INF in C:\\SYSTEM32\\RAS are not marked as read-only and the currently logged on user does have write permissions.

3. Reinstall RAS/DUN


699 - The device response caused buffer overflow.
Error 699

1. In the modem properties make sure that the port speed is not set too low.

2. Open up the " "Port Settings and make sure that FIFO's are on and not set too low. Try playing around with these settings until the error goes away.

3. Try uninstalling and reinstalling the modem.

4. Try uninstalling and reinstalling Dialup Networking and all its associated components.

5. Refer to computer manufacturer.


700 - The expanded command in the device .INF file is too
Error 700

1. Most likely one of the .INF or scripts has a line or command that is greater than 256 characters. This line/command will have to be broken up into multiple commands.


701 - The device moved to a BPS rate not supported by the
Error 701

1. Odd error. Try lowering the port speed and restricting the connect speed a bit with an init string. Could be a COM port or serial port problem.


702 - Device response received when none expected
Error 702

1. Make sure the modem is using correct drivers for the computer's operating system (most likely NT). Try reinstalling the modem.

2. Make sure that the files PAD.INF MODEM.INF and SWITCH.INF in C:\\SYSTEM32\\RAS are not marked as read-only and the currently logged on user does have write permissions.

3. Reinstall RAS/DUN.


703 - ERROR INTERACTIVE MODE
Error 703

1. A dbcc checkcatalog attempted on a database which has many objects (for example over 640 tables) may get a 703 error message. Thusly the memory request failed because more than 64 pages are required to run the query in its present form. The query should be broken up into shorter queries if possible. To fix this execute master.. More info on error 703 can be found at:
http://support.microsoft.com/support/kb/articles/q88/6/85.asp


704 - ERROR BAD CALLBACK NUMBER
Error 704

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login at that time of day. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid.


705 - ERROR INVALID AUTH STATE
Error 705

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Make sure that the user is typing in the proper username and password (and make sure nothing is under the Domain section in winNT/2k unless there is supposed to be)

4. In Win9x/ME make sure that secure pass isn't checked under server types and in Win2k/NT make sure that accept any auth including clear text is dotted.

5. Do a full reinstall of dialup related components.

6. If you are running Windows 2000 or NT check the event log for further details on this error.


706 - ERROR WRITING INITBPS
ERROR 706
ERROR WRITING INITBPS ::

NO FIX


707 - X.25 diagnostic indication.
Error 707

1. Clear out the X.25 tab in the windows NT phone book entry's properties. Set it to none. (Unless the user has an X.25 provider in which case have them contact the provider for diagnostic information.)


708 - The account has expired
Error 708

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login at that time of day. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password on the server side


709 - Error changing password on domain.
Error 709

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login at that time of day. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps reset their password on the server side.


710 - Serial overrun errors were detected while ...
Error 710

1. This is probably a modem error. In any case check the connectoid and Network settings. If they look good then...

2. Make sure modem is setup properly try inits check for updated drivers.

3. Lower the Fifo buffers. Try limiting the connect speed.

4. Check into line noise


711 - RasMan initialization failure. Check the event log.
Error 711

1. Check the event log to see if that actually tells you what the problem is.

2. Reboot.

3. Uninstall and reinstall RAS


712 - Biplex port is initializing. Wait a few seconds and
Error 712

1. Reboot. Wait a few moments. Try again.

2. Uninstall and reinstall the modem.

3. Uninstall and reinstall RAS/DUN.


713 - No active ISDN lines are available.
Error 713

1. Are they using ISDN? If so are they setup properly on both user and server sides? If not see if they are setup improperly for regular dialup.

2. Check their ISDN line make sure all devices are hung up and the modem/TA is hooked up properly.

3. Have the telco check the line


714 - Not enough ISDN channels are available to make the cal
Error 714

1. Are they using ISDN? If so are they setup properly on both user and server sides? If not see if they are setup improperly for regular dialup.

2. Check their ISDN line make sure all devices are hung up and the modem/TA is hooked up properly.

3. Have the telco check the line.


715 - Too many errors occurred because of poor phone line
Error 715

1. Make sure no devices are connected to the line. Try another piece of phone cord.

2. Try modem driver updates and inits.

3. Get a line noise test done.


716 - The Remote Access IP configuration is unusable.
Error 716

1. Make sure that the dialer is configured correctly. If so recreate the dialer.

2. Check network settings make sure bindings are correct.

3. Try reinstalling RAS/DUN


717 - No IP addrs are available in the static pool of addrs
Error 717

1. This happens when the user dials into an NT server. If you are using an NT server then perhaps you should allow them to login at that time of day. If not make sure they are dialing the correct phone number.

2. Recreate the connectoid. Perhaps make sure that they do not have a static IP specified or if they are supposed to and do make sure their static IP is not in use.


718 - PPP timeout
Error 718

1. Reboot the machine verify your Username and Password and try again. Check for realms if in NT make sure you have nothing under domain accept any auth including clear text is checked and try unchecking Enable PPP LCP extensions. Make sure logon to network isn't checked. Make sure that nothing is typed in the DOMAIN field if this is NT.

2. This is often a POP problem. Try logging onto a different POP. 718 is usually on the ISP's end but NOT ALWAYS. If there are multiple calls coming into the ISP's callcenter then they could see a problem but if not it is probably the user's computer.

3. Nuke the pwl files.

4. Have ISP reset the password.

5. Recreate connectoid.

6. Full uninstall and reinstall of connectoid network and DUN/RAS.

7. This can sometimes also be a communications problem caused by heavy line noise or modem problems. Try updating the modem drivers inits commas etc...and have a line noise test performed.

More info on error 718 can be found at:
http://www.deja.com/[ST_rn=qs]/qs.xp?QRY=microsoft+718&OP=dnquery.xp&ST=QS&DBS=2


719 - PPP terminated by remote machine.
Error 719

1. Reboot the machine verify your Username and Password and try again. Check for realms if in NT make sure you have nothing under domain accept any auth including clear text is checked and try unchecking Enable PPP LCP extensions. Make sure logon to network isn't checked. Make sure that nothing is typed in the DOMAIN field if this is NT.

2. This is often a POP problem. Try logging onto a different POP. 718 is usually on the ISP's end but NOT ALWAYS. If there are multiple calls coming into the ISP's callcenter then they could see a problem but if not it is probably the user's computer.

3. Nuke the pwl files.

4. Have ISP reset the password.

5. Recreate connectoid.

6. Full uninstall and reinstall of connectoid network and DUN/RAS.

7. This can sometimes also be a communications problem caused by heavy line noise or modem problems. Try updating the modem drivers inits commas etc...and have a line noise test performed.


720 - No PPP control protocols configured.
Error 720

1. Uninstall and Reinstall dialer network and DUN.

2. If NT: Try installing the Netbios interface service.

3. If NT: Try reinstalling the service pack.

4. Refer to manufacturer.


721 - Remote PPP peer is not responding.
Error 721

1. Reboot the machine verify your Username and Password and try again. Check for realms if in NT make sure you have nothing under domain accept any auth including clear text is checked and try unchecking Enable PPP LCP extensions. Make sure logon to network isn't checked. Make sure that nothing is typed in the DOMAIN field if this is NT.

2. This is often a POP problem. Try logging onto a different POP. 718 is usually on the ISP's end but NOT ALWAYS. If there are multiple calls coming into the ISP's callcenter then they could see a problem but if not it is probably the user's computer.

3. Nuke the pwl files.

4. Have ISP reset the password.

5. Recreate connectoid.

6. Full uninstall and reinstall of connectoid network and DUN/RAS.

7. This can sometimes also be a communications problem caused by heavy line noise or modem problems. Try updating the modem drivers inits commas etc...and have a line noise test performed.


722 - The PPP packet is invalid.
Error 722

1. Reboot the machine.

2. If it happens again try reinstalling DUN/RAS.


723 - The phone number including prefix and suffix is to
Error 723

1. Check the phone number. Make sure that it is correct including area code(if needed or not there if not needed) dialing a 9 call waiting etc..

2. Check to see if the dialer is setup to use a calling card.

3. Try recreating the dialer


724 - The IPX protocol cannot dial-out on the port because the..
Error 724

1. IPX? You aren't supposed to dial internet service with IPX. Check their settings and make sure they are using TCP/IP not IPX/SPX.

2. Perhaps they are trying to use VPN? Might want to disable that.


725 - The IPX protocol cannot dial-in on the port because ..
Error 725

1. IPX? You aren't supposed to dial internet service with IPX. Check their settings and make sure they are using TCP/IP not IPX/SPX.

2. Perhaps they are trying to use VPN? Might want to disable that.


726 -The IPX protocol can't be used for dial-out on more...
Error 726

1. IPX? You aren't supposed to dial internet service with IPX. Check their settings and make sure they are using TCP/IP not IPX/SPX.

2. Also are they trying to dialup more than once?

3. Perhaps they are trying to use VPN? Might want to disable that.


727 - Cannot access TCPCFG.DLL.
Error 727

1. Make sure that TCPCFG.DLL is not read only.

2. If you cannot find TCPCFG.DLL or this did not work try reinstalling RAS/DUN.


728 - Cannot find an IP adapter bound to Remote Access.
Error 728

1. Are the TCP/IP to RAS/DUN bindings correct? (it should be bound)

2. Uninstall/reinstall RAS/DUN.


729 - SLIP cannot be used unless the IP protocol is instal
Error 729

1. Make sure that dialer is set to use PPP that the dialer settings are correct the network settings are correct and that TCP/IP is installed in the network control panel.


730 - Computer registration is not complete.
Error 730

1. This should not happen when dialing into an ISP. Make sure the phone number is correct. A request for information on the status of computer registration was made before the information was made available so if the computer is dialing up for registration reboot and try again.


731 - The protocol is not configured.
Error 731

1. Make sure network and dialer settings are correct.

2. Uninstall and reinstall dialer network and DUN.

3. Check for modem driver updates and try modem inits. AT&F&C1&D2 as a generic 56k init and ATZ as a non-56k generic init.


732 - The PPP negotiation is not converging.
Error 732

1. In NT make sure accept any auth including clear text is checked. In 95/98 make sure logon to network is not checked and TCP/IP is checked.

2. Check for extra winsock.dll's (one in C:\\windows) and extra wsock32.dll's (one in c:\\windows\\system).

3. Check network settings.

4. Full uninstall and reinstall of connectoid network and DUN.


733 - The PPP control protocol for this network protocol ...
Error 733

1. Make sure PPP is selected in the connectoid. In NT turn off Enable PPP LCP extensions.

2. Make sure TCP/IP is checked.

3. Disable WINS in TCP/IP in network.

4. Uninstall and reinstall TCP/IP in network.


734 - The PPP link control protocol terminated..
Error 734

1. Make sure network and dialer settings are correct.

2. In NT: Try turning off PPP LCP extensions.

3. Could be an ISP problem. Check on this


735 - The requested address was rejected by the server..
Error 735

1. Make sure the dialer is not set to specify an IP address.

2. Make sure the network control panel is not requesting a specific ip address.

3. Check TCP/IP in the network control panel and set WINS to disabled. Also try it as DHCP if it is already disabled.


736 - The remote computer terminated the control protocol.
Error 736

1. If this is not a regular occurrence reboot and dial in again.

2. In NT: Try disabling PPP LCP extensions.

3. Try unchecking " "enable software compression in the dialer.

4. Could be on the ISP's end.


737 - Loopback detected..
Error 737

1. Check all of the dialer and network settings. Try removing any init strings from the modem.

2. Try uninstalling and reinstalling the modem.

3. Add E0 to any init string the computer may have been using or just use ATE0. This turns echo off. Basically the computer is echoing commands back to itself and thinks that it is trying to negotiate PPP with itself so this could fix it.


738 - The server did not assign an address.
Error 738

1. Turn off error control and compression in the modem settings.

2. Uncheck enable software compression (and PPP LCP extensions in NT).

3. In TCP/IP in the network control panel click on WINS and " "enable Windows Resolution" ".

4. Still in TCP/IP make sure that the IP is being attained automatically and (in NT) uncheck enable PPP LCP extensions.


739 - The remote server cannot use the WinNT encrypted pass
Error 739

1. In 95/98: Check dialer and make sure that " "require encrypted password/use secure auth is not checked. In NT: check dialer and make sure that " "Accept any auth including clear text is checked.


740 - The TAPI devices configured for Remote Access failed
Error 740

1. TAPI device error. Either the TAPI device was not installed properly or it just failed to initialize. Reinstall RAS and all TAPI devices.


741 - The local computer does not support encryption.
Error 741

1. Usually this means that the server is asking for secure password authentication. Usually ISPs do not require this probably about 99% of them. Make sure that the correct number is being dialed. Could be an ISP issue?

2. In 95/98: Check dialer and make sure that " "require encrypted password/use secure auth is not checked. In NT: check dialer and make sure that " "Accept any auth including clear text is checked.


742 - The remote server does not support encryption.
Error 742

1. In 95/98: Check dialer and make sure that " "require encrypted password/use secure auth is not checked. In NT: check dialer and make sure that " "Accept any auth including clear text is checked.


743 - The remote server requires encryption.
Error 743

1. Usually this means that the server is asking for secure password authentication. Usually ISPs do not require this probably about 99% of them. Make sure that the correct number is being dialed. Could be an ISP issue?

2. In 95/98: Check dialer and make sure that " "require encrypted password/use secure auth is not checked. In NT: check dialer and make sure that " "Accept any auth including clear text is checked.


744 - Can't use the IPX net number assigned by the remote
Error 744

1. Check network and dialer settings to make sure that it is not using IPX/SPX. If they are using it for a LAN check with the LAN administrator.

2. If they are not on a LAN remove any occurrences of IPX/SPX and try reinstalling TCP/IP


745 - An essential file is missing.
Error 745

1. Uninstall and reinstall Dial Up Networking.


http://support.microsoft.com/support/kb/articles/Q174/5/79.asp


746 - An essential file failed to initialize
ERROR 746
An essential file failed to initialize

NO FIX


747 - MAC not found.
ERROR 747
MAC not found.

NO FIX


748 - The system timedout while trying to load an essential
ERROR 748
The system timed out while trying to load an essential file.

NO FIX


749 - Invalid phone number.
ERROR 749
Invalid phone number.
Make sure the customer is using correct numbers::

Dallas - Waymark local TX
Area: Dallas
Access Number: 214.446.6276.
-------------------------------------------------
Ennis - Waymark local TX
Area: Ennis
Access Number: 469.641.0001.
-------------------------------------------------
Frisco - Waymark local TX
Area: Frisco
Access Number: 469.541.6276.
-------------------------------------------------
Ft. Worth - Waymark local TX
Area: Ft. Worth
Access Number: 817.259.6276.
-------------------------------------------------
Greenville - Waymark local TX
Area: Greenville
Access Number: 903.298.0001.
-------------------------------------------------
McKinney - Waymark local TX
Area: McKinney
Access Number: 469-541-6276...
-------------------------------------------------
Melissa - Waymark local TX
Area: Melissa
Access Number: 469-541-6276...
-------------------------------------------------
Midlothian - Waymark Local TX
Area: Midlothian
Access Number: 469-483-0001...
-------------------------------------------------
Red Oak - Waymark local TX
Area: Red Oak
Access Number: 469-725-0000...
-------------------------------------------------
Rockwall - Waymark local TX
Area: Rockwall
Access Number: 469-433-0001...
-------------------------------------------------
Waxahachie - Waymark local TX
Area: Waxahachie
Access Number: 469.280.0000.
-------------------------------------------------



750 - Invalid authentication attempt
ERROR 750
Invalid authentication attempt

NO FIX


751 - The callback number contains an invalid characters
751 - The callback number contains an invalid characters. Only the following characters are allowed: 0 to 9 T P W (" ") - @ and space

Error 751

1. In Win2k under Network & Dial-Up click on Advanced > Dial-Up Preferences > the Callback tab > and make sure that " "No Callback is selected.

2. If the user is supposed to be using callback make sure they using the correct dialup number/charactes as the error suggests.

3. Recreate the dailer.


752 - A syntax error was encountered while processing a sc
Error 752

1. The user is trying to use a script. Remove this script. If they need this script then try finding a syntax error/mistakes in the script.

2. If the script is " "needed because they need to use a terminal window then just check " "bring a terminal window up after dialing in the modem properties.


753 - The connection could not be disconnected because ...
Error 753

1. The user appears to be already dialed in. Disconnect or reboot.

2. Use the Routing and Remote Access service to disconnect the connection and make sure that nothing is attempting to dialup automatically with the wrong connection.

3. Recreate the dialer and delete any unused dialers.


754 - The system could not find the multi-link bundle.
Error 754

1. Reboot the machine.

2. Is the user supposed to be using Multilink? If not disable it if so reinstall the dialup components.

3. Check settings (DUN/RAS Network etc)

4. Do a full reinstall of dialup related components.

5. If you are running Windows 2000 or NT check the event log for further details on this error.


755 - The system cannot perform automated dial because ...
Error 755

1. Close any other programs that dialup like fax software trumpet sprydialer AOL etc.

2. Remove any of these programs from the systemif they are unneeded.

3. Recreate the dailer.

4. Reboot the machine.

5. Reinstall dialup/network components


756 - This connection is already being dialed.
Error 756

1. Close any other programs that dialup like fax software trumpet sprydialer AOL etc.

2. Remove any of these programs from the systemif they are unneeded.

3. Recreate the dailer.

4. Reboot the machine.

5. Reinstall dialup/network components


757 - Remote access services could not be started automati
Error 757

1. Reboot the machine.

2. Check settings (DUN/RAS Network etc)

3. Do a full reinstall of dialup related components.

4. If you are running Windows 2000 or NT check the event log for further details on this error.


758 - Internet connection sharing is already enabled on comp
Error 758

1. Reboot. In the connection properties check the Enable Internet connection sharing box under the Internet connection sharing tab make sure to select a LAN connection from the list.

2. Remove Internet Connection Sharing (it is mostly unsupported if removing it fixes it it is up to the user or network admin to figure it out).


760 - Error occurred while routing capabilities were enabled
Error 760

1. Check the dialer settings making sure that the user isn't set to static IP addressing (less they are supposed to) and that all other settings are ok.

2. Reinstall TCP/IP.

3. Reboot the computer.

4. Reinstall all dialup components.


761 - An error occurred while Internet connection sharing
Error 761

1. Make sure that Internet Connection Sharing is set to LAN.

2. Disable Internet Connection Sharing and contact the Network Admin to get it running properly.


763 - Internet connection sharing cannot be enabled
Error 763

1. Make sure that Internet Connection Sharing is set to LAN.

2. Disable Internet Connection Sharing and contact the Network Admin to get it running properly


764 - No smart card reader is installed.
Error 764

1. In the connection settings under the Security tab make sure that any auth is allowed.

2. Check the other dialer settings.

3. Recreate the dialer.

4. The user may need a Smart Card Reader as setup by their Network Admin.


765 - ICsharing can't be enabled. A LAN connection
Error 765

1. Make sure that Internet Connection Sharing is set to LAN.

2. Disable Internet Connection Sharing and contact the Network Admin to get it running properly


766 - The system could not find any certificate
Error 766

1. Have the user goto the following website to obtain a valid certificate:

http://windows.microsoft.com/windows2000/en/professional/help/sag_cswprocs_reqcert.htm


767 - ICsharing cannot be enabled. The LAN connection ...
767 - Internet connection sharing cannot be enabled. The LAN connection selected on the private network has more than one IP address configured. Reconfigure the LAN connection with a single IP address before enabling Internet connection sharing.

Error 767

1. Check the dialer settings making sure that the user isn't set to static IP addressing (less they are supposed to) and that all other settings are ok.

2. Reinstall TCP/IP.

3. Reboot the computer.

4. Reinstall all dialup components.


768 - connection attempt failed because of failure to encrypt ..
Error 768

1. Disable encryption in the connection properties


769 - The specified destination is not reachable
Error 769

1. Check the dialer settings making sure that the user isn't set to static IP addressing (less they are supposed to) and that all other settings are ok.

2. Reinstall TCP/IP.

3. Reboot the computer.

4. Reinstall all dialup components.


770 - The remote machine rejected the connection attempt.
Error 770

1. This is probably a modem error. In any case check the connectoid and Network settings. If they look good then...

2. Make sure modem is setup properly try inits check for updated drivers.

3. Lower the Fifo buffers. Lower port speed to 57600 making sure the checkbox to 'only connect at this speed' is unchecked.

4.1. Click Start goto find and click files or folders.

4.2. Search for telephon.ini.

4.3. If you find it then rename it to telephon.old or telephon.bad.

4.4. Click on Start Run then type tapiini.exe press Enter.

4.5. Reboot.

5. Check into line noise


771 - The connection attempt failed because the network is busy
Error 771

1. Make sure the user is dialing the correct phone number. Make sure the phone number they are dialing is not having issues.

2. Check the connectoid and Network settings.

3. Make sure modem is setup properly try inits check for updated drivers.

4. Lower the Fifo buffers. Lower port speed to 57600 making sure the checkbox to 'only connect at this speed' is unchecked.

5. Check into line noise.


772 - The remote computer's network hardware is incompatible
Error 772

1. Make sure the dialer is setup properly. It should be an actual dialer and not setup for LAN use.

2. See Network Admin.


773 - The connection attempt failed because the destination
Error 773

1. Make sure the user is dialing the correct phone number (check area code etc). Make sure the phone number they are dialing is not having issues.


774 - The connection attempt failed because of a temporary fail
Error 774

1. Reboot.

2. Check dialer settings.

3. Reinstall dialup components.


775 - The call was blocked by the remote computer.
Error 775

1. Make sure the correct number is being dialed (check area code etc.)

2. Make sure the number is not experiencing an outage.

3. Make sure user is not out of time for the day etc if this applies to the ISP.

4. Try disabling call waiting if the location has call waiting.

5. Does the number you are dialing from have voice mail? Voice mail can cause this and you will want to check your voicemail. If this becomes a common problem you may wish to reconsider having Voice mail on the number the computer dials from.


776 - The call couldn't be connected because the destination
Error 776

1. Make sure the dialer is setup properly. It should be an actual dialer and not setup for LAN use.

2. See Network Admin


777 - The connection attempt failed because the modem on the ..
Error 777

1. The modem isn't working. If external powercycle it if internal reboot the computer.

2. Make sure the modem is plugged in securely. This includes external cables and the PCI or ISA slot seating if internal.

3. Make sure the computer is not trying to dial multiple connections that it has no fax software etc using the modem.

4. Reinstall the modem.

5. Contact OEM.


778 - It was not possible to verify the id of the sever
Error 778

1. Make sure the user is dialing the correct phone number. Make sure the phone number they are dialing is not having issues.

2. Check the connectoid and Network settings.

3. Make sure there is not an outage on that phone number.

4. Make sure modem is setup properly try inits check for updated drivers.

5. Lower the Fifo buffers. Lower port speed to 57600 making sure the checkbox to 'only connect at this speed' is unchecked.

6. Check into line noise.


779 - To dial out using this connection you must use ....
779 - To dial out using this connection you must use a smart card.

Error 779

1. In the connection settings under the Security tab make sure that any auth is allowed.

2. Check the other dialer settings.

3. Recreate the dialer.

4. The user may need a Smart Card Reader as setup by their Network Admin.


780 - An attempted function is not valid for this connection
Error 780

1. Make sure the dialer is setup properly. It should be an actual dialer and not setup for LAN use.

2. See Network Admin.


781 - The encryption attempt failed because no valid cert. found
Error 781

1. Have the user goto the following website to obtain a valid certificate:

http://windows.microsoft.com/windows2000/en/professional/help/sag_cswprocs_reqcert.htm


782 - Network Address Translation (NAT) is currently ...
ERROR 782
Network Address Translation (NAT) is currently installed as a routing protocol and must be removed before enabling Internet Connection Sharing

NO FIX


783 - Internet Connection Sharing cannot be enabled...
ERROR 783
Internet Connection Sharing cannot be enabled. The LAN connection selected as the private network is either not present or is disconnected from the network. Please ensure that the LAN adapter is connected before enabling Internet Connection Sharing

NO FIX


784 - You cannot dial using this connection at logon time" "" ERROR 784
You cannot dial using this connection at logon time because it is configured to use a user name different than the one on the smart card. If you want to use it at logon time you must configure it to use the user name on the smart card

NO FIX


785 - You cannot dial using this connection at logon time..
ERROR 785
You cannot dial using this connection at logon time because it is not configured to use a smart card. If you want to use it at logon time you must edit the properties of this connection so that it uses a smart card

NO FIX


786 - The L2TP connection attempt failed because there is
ERROR 786
The L2TP connection attempt failed because there is no valid machine certificate on your computer for security authentication

NO FIX


787 - The L2TP connection attempt failed because the secure
ERROR 787

The L2TP connection attempt failed because the security layer could not authenticate the remote computer

NO FIX


788 - The L2TP connection attempt failed because the secur
ERROR 788
The L2TP connection attempt failed because the security layer could not negotiate compatible parameters with the remote computer

NO FIX


789 - The L2TP connection attempt failed because the secure
ERROR 789
The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer

NO FIX


790 - The L2TP connection attempt failed because certif
ERROR 790
The L2TP connection attempt failed because certificate validation on the remote computer failed

NO FIX


791 - The L2TP connection attempt failed because security
ERROR 791
The L2TP connection attempt failed because security policy for the connection was not found

NO FIX


792 - The L2TP conn. attempt failed because security....
ERROR 792
The L2TP connection attempt failed because security negotiation timed out

NO FIX


793 - The L2TP connection attempt failed because an error ....
ERROR 793
The L2TP connection attempt failed because an error occurred while negotiating security

NO FIX


794 - The Framed Protocol RADIUS attribute for this user ...
ERROR 794
The Framed Protocol RADIUS attribute for this user is not PPP

NO FIX


795 - The Tunnel Type RADIUS attribute for this user...
ERROR 795
The Tunnel Type RADIUS attribute for this user is not correct

NO FIX


796 - The Service Type RADIUS attribute for this user ...
ERROR 796
The Service Type RADIUS attribute for this user is neither Framed nor Callback Framed

NO FIX


797 - A connection to the remote computer couldn't be ...
ERROR 797
A connection to the remote computer could not be established because the modem was not found or was busy

NO FIX

797 - The modem could not be found.

This error occurs only in Windows 2000 and XP. The error can occur if the modem is no longer visible to the system and may be a problem related to the modem driver or system conflicts that cause the modem to work only some of the time.

In some cases rebooting the machine may " "solve the problem.

If the error persists check to see if there is an WINDOWS XP

- [img:f74b16d8ba]http://www.modemhelp.net/screenshots/icons/win2ksplash.gif[/img:f74b16d8ba] - WIN 2K

- [img:f74b16d8ba]http://www.modemhelp.net/screenshots/icons/winmesplash.gif[/img:f74b16d8ba] - WINDOWS ME

- [img:f74b16d8ba]http://www.modemhelp.net/screenshots/icons/win98splash.gif[/img:f74b16d8ba] - WINDOWS 98/SE

- [img:f74b16d8ba]http://www.modemhelp.net/screenshots/icons/win95splash.gif[/img:f74b16d8ba] - WINDOWS 95 v.1.0
- WINDOWS 95 v.1.2
- WINDOWS 95 v.1.3[/list:u:f74b16d8ba]


Well Known Port Numbers 0-1024
[list:0333e9595f]PORT-PROTOCOL-KEYWORD-DESCRIPTION

0-" "tcp- udp" "--Reserved
1-" "tcp- udp" "-tcpmux-TCP Port Service Multiplexer rfc-1078
2-" "tcp- udp" "-compressnet-Management Utility
3-" "tcp- udp" "-compressnet-Compression Process
4-" "tcp- udp" "-echo-AppleTalk Echo Protocol
5-" "tcp- udp" "-rje-Remote Job Entry
6-ddp-zip-Zone Information Protocol
7-" "tcp- udp" "-echo-Echo
8-" "tcp- udp" "--Unassigned
9-" "tcp- udp" "-discard-Discard; alias=sink null
10-" "tcp- udp" "--Unassigned
11-" "tcp- udp" "-systat-Active Users; alias=users
12-" "tcp- udp" "--Unassigned
13-" "tcp- udp" "-daytime-Daytime
14-" "tcp- udp" "--Unassigned
15-" "tcp- udp" "--Unassigned [was netstat]
16-" "tcp- udp" "--Unassigned
17-tcp-qotd-Quote of the Day; alias=quote
18-" "tcp- udp" "-msp-Message Send Protocol
19-" "tcp- udp" "-chargen-Character Generator; alias=ttytst source
20-tcp-ftp-data-File Transfer [Default Data]
21-tcp-ftp-" "File Transfer [Control">- connection dialog" "
22-tcp-ssh-Secure Shell Login
22-udp-pcanywhere-PC Anywhere
23-tcp-telnet-Telnet
24-tcp-priv-mail-Any private mail system
25-tcp-smtp-Simple Mail Transfer; alias=mail
26-tcp udp--Unassigned
27-tcp-nswfe-NSW User System FE
28-tcp udp--Unassigned
29-tcp-msgicp-MSG ICP
30-tcp udp--Unassigned
31-tcp-msgauth-MSG Authentication
32-tcp udp--Unassigned
33-tcp udp-dsp-Display Support Protocol
34-tcp udp--Unassigned
35-tcp udp-priv-print-Any private printer server
36-tcp udp--Unassigned
37-tcp udp-time-Time; alias=timeserver
38-tcp udp-rap-Remote Access Protocol
39-tcp udp-rlp-Resource Location Protocol; alias=resource
40-tcp udp--Unassigned
41-" "tcp- udp" "-graphics-Graphics
41-" "tcp- udp" "-deepthroat-Deep Throat Trpjan Horse
42-tcp udp-nameserver-Host Name Server; alias=nameserver
43-tcp udp-nicname-Who Is; alias=nicname
44-tcp udp-mpm-flags-MPM FLAGS Protocol
45-tcp udp-mpm-Message Processing Module [recv]
46-tcp udp-mpm-snd-MPM [default send]
47-tcp udp-ni-ftp-NI FTP
48-tcp udp-auditd-Digital Audit Daemon
49-tcp udp-tacacs-Login Host Protocol (TACACS)
50-tcp udp-re-mail-ck-Remote Mail Checking Protocol
51-tcp udp-la-maint-IMP Logical Address Maintenance
52-tcp udp-xns-time-XNS Time Protocol
53-tcp udp-domain-Domain Name Server
54-tcp udp-xns-ch-XNS Clearinghouse
55-tcp udp-isi-gl-ISI Graphics Language
56-tcp udp-xns-auth-XNS Authentication
57-tcp udp-priv-term-Any private terminal access
58-tcp udp-xns-mail-XNS Mail
59-tcp udp-priv-file-Any private file service
60-tcp udp--Unassigned
61-tcp udp-ni-mail-NI MAIL
62-tcp udp-acas-ACA Services
63-tcp udp-via-ftp / whois++-VIA Systems - FTP / whois++
64-tcp udp-covia-Communications Integrator ( Cl )
65-tcp udp-tacacs-ds-TACACS-Database Service
66-tcp udp-sql*net-Oracle SQL*NET
67-tcp udp-bootps-DHCP BOOTP Protocol Server
68-tcp udp-bootpc-DHCP BOOTP Protocol Client
69-tcp udp-tftp-Trivial File Transfer
70-tcp udp-gopher-Gopher
71-tcp udp-netrjs-1-Remote Job Service
72-tcp udp-netrjs-2-Remote Job Service
73-tcp udp-netrjs-3-Remote Job Service
74-tcp udp-netrjs-4-Remote Job Service
75-udp-priv-dial-Any private dial out service
76-tcp udp-deos-Distributed External Object Store
77-tcp udp-priv-rjs-Any private RJE service
78-tcp udp-vettcp-Vettcp
79-tcp udp-finger-Finger
80-tcp udp-WWW-World Wide Web HTTP
81-tcp udp-hosts2-ns-HOSTS2 Name Server
82-tcp udp-xfer-XFER Utility
83-tcp udp-mit-ml-dev-MIT ML Device
84-tcp udp-ctf-Common Trace Facility
85-tcp udp-mit-nil-dev-MIT ML Device
86-tcp udp-mfcobol-Micro Focus Cobol
87-tcp udp-ttylink-Any private terminal link; alias=ttylink
88-tcp udp-kerberos-sec-Kerberos( v5 ) krb5
89-tcp udp-su-mit-tg-SU/MIT Telnet Gateway
PORT 90 also being used unofficially by Pointcast-
90-tcp udp-DNSIX-DNSIX Security Attribute Token Map
91-tcp udp-mit-dov-MIT Dover Spooler
92-tcp udp-npp-Network Printing Protocol
93-tcp udp-dcp-Device Control Protocol
94-tcp udp-objcall-Tivoli Object Dispatcher
95-tcp-supdup-BSD supupd( 8 )
96-tcp udp-dixie-DIXIE Protocol Specification
97-tcp udp-swift-rvf-Swift Remote Virtual File Protocol
98-tcp-linuxconf-linuxconf
98-udp-tacnews-TAC News
99-tcp udp-metagram-Metagram Relay
100-tcp -newacct-[unauthorized use]
101-tcp udp-hostriame-NIC Host Name Server; alias=hostname
102-tcp udp-iso-tsap-ISO-TSAP Class 0
103-tcp udp-gppitnp-Genesis Point-to-point Trans Net or X400 ISO Email; alias=webster
104-tcp udp-acr-nema-ACR-NEMA Digital Imag. & Comm. 300
105-tcp udp-csnet-ns-Mailbox Name Nameserver
106-tcp udp-3com-tsmux-" "3COM-TSMUX- Eudora compatible PW changer" "
107-tcp udp-rtelnet-Remote Telnet Service
108-tcp udp-snagas-SNA Gateway Access Server
109-tcp udp-pop2-Post Office Protocol - Ver 2; alias=postoffice
110-tcp udp-pop3-Post Office Protocol - Ver 3; alias=postoffice
111-tcp udp-sunrpc-" "SUN Remote Procedure Call- rpcbind" "
112-tcp udp-mcidas-McIDAS Data Transmission Protocol
113-tcp udp-auth-" "ident- tap- Authentication Service" "
114-tcp udp-audionews-Audio News Multicast
115-tcp udp-sftp-Simple File Transfer Protocol
116-tcp udp-ansanotify-ANSA REX Notify
117-tcp udp-uucp-path-UUCP Path Service
118-tcp udp-sqIserv-SQL Services
119-tcp udp-nntp-Network News Transfer Protocol; alias=usenet
120-tcp udp-cfdptkt-CFDPTKT
121-tcp udp-erpc-Encore Expedited Remote Pro.Call
121-tcp udp-jammerkilla-BO Jammer Killa Trojan Horse
122-tcp udp-smakynet-SMAKYNET
123-tcp udp-ntp-Network Time Protocol; alias=ntpd ntp
124-tcp udp-ansatrader-ANSA REX Trader
125-tcp udp-locus-map-Locus PC-Interface Net Map Server
126-tcp udp-nxedit-NXEdit - Previously: Unisys Unitary Login
127-tcp udp-locus-con-Locus PC-Interface Conn Server
128-tcp udp-gss-xlicen-GSS X License Verification
129-tcp udp-pwdgen-Password Generator Protocol
130-tcp udp-cisco-fna-Cisco FNATIVE
131-tcp udp-cisco-tna-Cisco TNATIVE
132-tcp udp-cisco-sys-Cisco SYSMAINT
133-tcp udp-statsrv-Statistics Service
134-tcp udp-ingres-net-INGRES-NET Service
135-tcp udp-loc-srv / epmap-Location Service / DCE endpoint resolution
136-tcp udp-profile-PROFILE Naming System
137-tcp udp-netbios-ns-NetBIOS Name Service
138-tcp udp-netbios-dgm-NetBIOS Datagram Service
139-tcp udp-netbios-ssn-NetBIOS Session Service
140-tcp udp-emfis-data-EMFIS Data Service
141-tcp udp-emfis-cntl-EMFIS Control Service
142-tcp udp-bl-idm-Britton-Lee IDM
143-tcp udp-imap2-Internet Message Access Protocol v2
144-tcp udp-NeWs-
145-tcp udp-uaac-UAAC Protocol
146-tcp udp-iso-ip0-ISO-IP0
147-tcp udp-iso-ip-ISO-IP
148-tcp udp-cronus / jargon-CRONUS-SUPPORT / Jargon
149-tcp udp-aed-512-AED 512 Emulation Service
150-tcp udp-sql-net-SQL-NET
151-tcp udp-hems-HEMS
152-tcp udp-bftp-Background File Transfer Program
153-tcp udp-sgmp-SGMP; alias=sgmp
154-tcp udp-netsc-prod-Netscape
155-tcp udp-netsc-dev-Netscape
156-tcp udp-sqlsrv-SQL Service
157-tcp udp-knet-cmp-KNET/VM Command Message Protocol
158-tcp udp-pcmail-srv-PCMail Server; alias=repository
159-tcp udp-nss-routing-NSS-Routing
160-tcp udp-sginp-traps-SGMP-TRAPS
161-tcp udp-sump-SNMP; alias=snmp
162-tcp udp-snmptrap-SNMP-trap
163-tcp udp-cmip-man-CMIP TCP Manager
164-tcp udp-cmip/smip-agent-CMIP TCP Agent
165-tcp udp-xns-courier-Xerox
166-tcp udp-s-net-Sirius Systems
167-tcp udp-namp-NAMP
168-tcp udp-rsvd-RSVD
169-tcp udp-send-SEND
170-tcp udp-print-srv-Network PostScript
171-tcp udp-multiplex-Network Innovations Multiplex
172-tcp udp-cl-1-Network Innovations CL/1
173-tcp udp-xyplex-mux-Xyplex
174-tcp udp-mailq-MAILQ
175-tcp udp-vmnet-VMNET
176-tcp udp-genrad-mux-GENRAD-MUX
177-tcp udp-xdmcp-X Display Manager Control Protocol
178-tcp udp-nextstep-NextStep Window Server
179-tcp udp-bgp-Border Gateway Protocol
180-tcp udp-ris-Intergraph
181-tcp udp-unify-Unify
182-tcp udp-audit-Unisys Audit SITP
183-tcp udp-ocbinder-OCBinder
184-tcp udp-ocserver-OCServer
185-tcp udp-remote-kis-Remote-KIS
186-tcp udp-kis-KIS Protocol
187-tcp udp-aci-Application Communication Interface
188-tcp udp-mumps-Plus Five's MUMPS
189-tcp udp-qft-Queued File Transport
190-tcp udp-gacp/cacp-Gateway Access Control Protocol
191-tcp udp-prospero-Prospero Directory Service
192-tcp udp-osu-nms-OSU Network Monitoring System
193-tcp udp-srmp-Spider Remote Monitoring Protocol
194-tcp udp-irc-Internet Relay Chat Protocol
195-tcp udp-dn6-nlm-aud-DNSIX Network Level Module Audit
196-tcp udp-dn6-smm-red-DNSIX Session Mgt Module Audit Redir
197-tcp udp-dls-Directory Location Service
198-tcp udp-dls-mon-Directory Location Service Monitor
199-tcp udp-smux-SNMP Unix Multiplexer
200-tcp udp-src-IBM System Resource Controller
201-tcp udp-at-rtmp-AppleTalk Routing Maintenance
202-tcp udp-at-nbp-AppleTalk Name Binding
203-tcp udp-at-3-AppleTalk Unused
204-tcp udp-at-echo-AppleTalk Echo
205-tcp udp-at-5-AppleTalk Unused
206-tcp udp-at-zis-AppleTalk Zone Information
207-tcp udp-at-7-AppleTalk Unused
208-tcp udp-at-8-AppleTalk Unused
209-tcp udp-tam / qmtp-Trivial Authenticated Mail Protocol / The Quick Transfer Protocol
210-tcp udp-z39.50-" "wais- ANSI Z39.50" "
211-tcp udp-914c/g-Texas Instruments 914C/G Terminal
212-tcp udp-anet-ATEXSSTR
213-tcp udp-ipx-IPX
214-tcp udp-vmpwscs-VM PWSCS
215-tcp udp-softpc-Insignia Solutions
216-tcp udp-Atls / CAIlic-(Access Technology / Computer Associates ) License Server
217-tcp udp-dbase-dBASE UNIX
218-tcp udp-mpp-Netix Message Posting Protocol
219-tcp udp-uarps-Unisys ARPs
220-tcp udp-imap3-Interactive Mail Access Protocol v3
221-tcp udp-fln-spx-Berkeley rlogind with SPX auth
222-tcp udp-rsh-spx-" "Berkeley rshd. with SPX auth- Possible conflicy with " "" "Masqdialer" "
223-tcp udp-cdc-Certificate Distribution Center
224-tcp udp-masqdialer-masqdialer
225-241---Reserved
242-tcp udp-direct-Direct
243-tcp udp-sur-meas-Survey Measurement
244-tcp udp-dayna-dayna
245-tcp udp-link-LINK
246-tcp udp-dsp3270-Display Systems Protocol
247-tcp udp-subntbcst_tftp-SUBNTBCST_TFTP
248-tcp udp-bhfhs-bhfhs
249-255-tcp udp--Reserved
256-tcp udp-rap-RAP
257-tcp udp-set-Secure Electronic Transaction
258-tcp udp-yak-chat-Yak Winsock Personal Chat
259-tcp udp-escro-gen-Efficient Short Romote Operations
260-tcp udp-openport-Openport
261-tcp udp-nsiiops-IIOP Name Service TLS/SSL
262-tcp udp-arcisdms-Arcisdms
263-tcp udp-hdap-HDAP
264-tcp udp-bgmp-BGMP
265-tcp udp-x-bone-ctl-X-Bone CTL
267-tcp udp-td-service-Tobit David Service Layer
268-tcp udp-td-replica-Tobit David Replica
269-279---Unassigned
280-tcp udp-http-mgmt-http-mgmt
281-tcp udp-personal-link-Personal-Link
282-tcp udp-cableport-ax-Cable Port A/X
283-tcp udp-rescap-rescap
284-tcp udp-corerjd-corerjd
285-tcp udp--Unassigned
286-tcp udp-fxp-1-FXP-1
287-tcp udp-k-block-K-Block
288-307---Unassigned
308-tcp udp-novastorbakcup-Novastor Backup
309-tcp udp-entrusttime-EntrustTime
310-tcp udp-bhmds-bhmds
311-tcp udp-asip-webadmin-AppleShare IP WebAdmin
312-tcp udp-vslmp-VSLMP
313-tcp udp-magenta-logic-netfusion.co.uk
314-tcp udp-opalis-robot-Opalis Robot
315-tcp udp-dpsi-DPSI
316-tcp udp-decauth-decAuth
317-tcp udp-zannet-Zannet
318-tcp udp-pkix-timestamp-PKIX TimeStamp
319-tcp udp-ptp-event-PTP Event
320-tcp udp-ptp-general-PTP General
321-tcp udp-pip-PIP
322-tcp udp-rtsps-RTSPS
323-332---Unassigned
333-tcp udp-texar-Texar Security Port
334-343-tcp udp--Unassigned
344-tcp udp-pdap-Propero Data Access Protocol
345-tcp udp-pawserv-Perf Analysis Workbench
346-tcp udp-zserv-Zebra server
347-tcp udp-fatserv-Fatmen Server
348-tcp udp-csi-sgwp-Cabletron Management Protocol
349-tcp udp-mftp-mftp
350-tcp udp-matip-type-a-MATIP Type A
351-tcp udp-matip-type-b-MATIP Type B or bhoetty
352-tcp udp-dtag-ste-sb-DTAG or bhoedap4
353-tcp udp-ndsauth-NDSAUTH
354-tcp udp-bh611-bh611
355-tcp udp-datex-asn-DATEX-ASN
356-tcp udp-cloanto-net-1-Cloanto Net 1
357-tcp udp-bhevent-bhevent
358-tcp udp-shrinkwrap-Shrinkwrap
359-tcp udp-tenebris_nts-Tenebris Network Trace Service
360-tcp udp-scoi2odialog-scoi2odialog
361-tcp udp-semantix-Semantix
362-tcp udp-srssend-SRS Send
363-tcp udp-rsvp_tunnel-RSVP Tunnel
364-tcp udp-aurora_tunnel-Aurora CMGR
365-tcp udp-dtk-Deception Tool Kit (lame www.all.net)
366-tcp udp-odmr-ODMR (On-Demand Mail Relay)
367-tcp udp-mortgageware-MortgageWare
368-tcp udp-qbikgdp-QbikGDP
369-tcp udp-rpc2portmap-rpc2portmap
370-tcp udp-codaauth2-codaauth2
371-tcp udp-clearcase-Clearcase
372-tcp udp-ulistserv / ulistproc-UNIX Listserv / ListProcessor
373-tcp udp-legent-1-Legent Corporation (now Computer Associates)
374-tcp udp-legent-2-Legent Corporation (now Computer Associates)
375-tcp udp-hassle-Hassle
376-tcp udp-nip-Amiga Envoy Network Inquiry Protocol
377-tcp udp-tnETOS-NEC Corporation
378-tcp udp-dsETOS-NEC Corporation
379-tcp udp-is99c-TIA/EIA/IS-99 modem client
380-tcp udp-is99s-TIA/EIA/IS-99 modem server
381-tcp udp-hp-collector-HP performance data collector
382-tcp udp-hp-managed-node-HP performance data managed node
383-tcp udp-hp-alarm-mgr-HP performance data alarm manager
384-tcp udp-arns-A Remote Network Server System
385-tcp udp-ibm-app-IBM Application
386-tcp udp-asa-ASA Message Router Object Def.
387-tcp udp-aurp-AppleTalk Update-Based Routing Protocol
388-tcp udp-unidata-ldm-Unidata LDM Version 4
389-tcp udp-ldap-Lightweight Directory Access Protocol
390-tcp udp-uis-UIS
391-tcp udp-synotics-relay-SynOptics SNMP Relay Port
392-tcp udp-synotics-broker-SynOptics Port Broker Port
393-tcp udp-dis-Data Interpretation System
394-tcp udp-embl-ndt-EMBL Nucleic Data Transfer
395-tcp udp-netcp-NETscout Control Protocol
396-tcp udp-netware-ip-Novell Netware over IP
397-tcp udp-mptn-Multi Protocol Trans. Net.
398-tcp udp-krypolan-Kryptolan
399-tcp udp-iso-tsap-c2-ISO Transport Class 2 Non-Control over TCO
400-tcp udp-work-sol-Workstation Solutions
401-tcp udp-ups-Uninterruptible Power Supply
402-tcp udp-genie-Genie Protocol
403-tcp udp-decap-decap
404-tcp udp-nced-nced
405-tcp udp-ncld-ncld
406-tcp udp-imsp-Interactive Mail Support Protocol
407-tcp udp-timbuktu-Timbuktu
408-tcp udp-prm-sm-Prospero Resource Manager Sys. Man.
409-tcp udp-prm-nm-Prospero Resource Manager Node Man.
410-tcp udp-decladebug-DECLadebug Remote Debug Protocol
411-tcp udp-rmt-Remote MT Protocol
412-tcp udp-synoptics-trap-Trap Convention Port
413-tcp udp-smsp-SMSP
414-tcp udp-infoseek-InfoSeek
415-tcp udp-bnet-BNet
416-tcp udp-silverplatter-Silverplatter
417-tcp udp-onmux-Onmux
418-tcp udp-hyper-g-Hyper-G
419-tcp udp-ariel1-Ariel
420-tcp udp-smpte-SMPTE
421-tcp udp-ariel2-Ariel
422-tcp udp-ariel3-Ariel
423-tcp udp-opc-job-start-IBM Operations Planning and Control Start
424-tcp udp-opc-job-track-IBM Operations Planning and Control Track
425-tcp udp-icad-el-ICAD
426-tcp udp-smartsdp-smartsdp
427-tcp udp-svrloc-Server Location
428-tcp udp-ocs_cmu-OCS_CMU
429-tcp udp-ocs_amu-OCS_AMU
430-tcp udp-utmpsd-UTMPSD
431-tcp udp-utmpcd-UTMPCD
432-tcp udp-iasd-IASD
433-tcp udp-nnsp-" "usenet- Network News Transfer" "
434-tcp udp-mobile-agent-MobileIP-Agent
435-tcp udp-mobile-mn-MobilIP-ML
436-tcp udp-dna-cml-DNA-CML
437-tcp udp-comscm-comscm
438-tcp udp-dsfgw-dsfgw
439-tcp udp-dasp-dasp
440-tcp udp-sgcp-sgcp
441-tcp udp-decvms-sysmgt-decvms-sysmgt
442-tcp udp-cvc_hostd-cvc_hostd
443-tcp udp-https-http protocol over TLS/SSL
444-tcp udp-snpp-Simple Network Paging Protocol
445-tcp udp-microsoft-ds-Microsoft-DS
446-tcp udp-ddm-rdb-DDM-RDB
447-tcp udp-ddm-dfm-DDM-RFM
448-tcp udp-ddm-ssl-aam-byte
449-tcp udp-as-servermap-AS Server Mapper
450-tcp udp-tserver-TServer
451-tcp udp-sfs-smp-net-Cray Network Semaphore server
452-tcp udp-sfs-config-Cray SFS config server
453-tcp udp-creativeserver-CreativeServer
454-tcp udp-contentserver-ContentServer
455-tcp udp-creativepartnr-CreativePartnr
456-tcp udp-macon-tcp/udp-macon-tcp/udp
456-tcp udp-HackerParadise-Hackers Paradise Trojan
457-tcp udp-scohelp-scohelp
458-tcp udp-appleqtc-Apple Quick Time TV/Conferencing
459-tcp udp-ampr-rcmd-ampr-rcmd
460-tcp udp-skronk-skronk
461-tcp udp-datasurfsrv-DataRampSrv
462-tcp udp-datasurfsrvsec-DataRampSrvSec
463-tcp udp-alpes-alpes
464-tcp udp-kpasswd-kerberos ( v5 )
465-tcp udp-smtps-smtp protocol over TLS/SSL (was ssmtp)
466-tcp udp-digital-vrc-digital-vrc
467-tcp udp-mylex-mapd-mylex-mapd
468-tcp udp-photuris-proturis
469-tcp udp-rcp-Radio Control Protocol
470-tcp udp-scx-proxy-scx-proxy
471-tcp udp-mondex-Mondex
472-tcp udp-ljk-login-ljk-login
473-tcp udp-hybrid-pop-hybrid-pop
474-tcp udp-tn-tl-w1-tn-tl-w1
475-tcp udp-tcpnethaspsrv-tcpnethaspsrv
476-tcp udp-tn-tl-fd1-tn-tl-fd1
477-tcp udp-ss7ns-ss7ns
478-tcp udp-spsc-spsc
479-tcp udp-iafserver-iafserver
480-tcp udp-iafdbase -iafdbase
481-tcp udp-des/ph-Ph service
482-tcp udp-bgs-nsi/xlog-
483-tcp udp-ulpnet-ulpnet
484-tcp udp-integra-sme-Integra Software Management Environment
485-tcp udp-powerburst-Air Soft Power Burst
486-tcp udp-sstat/avian-
487-tcp udp-saft-saft Simple Asynchronous File Transfer
488-tcp udp-gss-http-gss-http
489-tcp udp-nest-protocol-nest-protocol
490-tcp udp-micom-pfs-micom-pfs
491-tcp udp-go-login-go-login
492-tcp udp-ticf-1-Transport Independent Convergence for FNA
493-tcp udp-ticf-2-Transport Independent Convergence for FNA
494-tcp udp-pov-ray-POV-Ray
495-tcp udp-intecourier-intecourier
496-tcp udp-pim-rp-disc-PIM-RP-DISC
497-tcp udp-dantz-dantz
498-tcp udp-siam-siam
499-tcp udp-iso-ill-ISO ILL Protocol
500-tcp udp-isakmp-internet Secuirty Association and Key management protocol
501-tcp udp-stmf-STMF
502-tcp udp-asa-appl-proto-asa-appl-proto
503-tcp udp-intrinsa-Intrinsa
504-tcp udp-citadel-citadel
505-tcp udp-mailbox-lm-mailbox-lm
506-tcp udp-ohimsrv-ohimsrv
507-tcp udp-crs-crs
508-tcp udp-xvttp-xvttp
509-tcp udp-snare-snare
510-tcp udp-fcp-FirstClass Protocol
511-tcp udp-passgo-PassGo
512-tcp-print / exec-" "BSD rexecd- Windows NT Server and Windows NT Workstation version 4.0 can send LPD client print jobs from any available reserved port between 512 and 1023. See also description for ports 721 to 73 1" "-
---Remote process execution; authentication performed using UNIX loppgin names
512-udp-biff-comsat
513-tcp-login-BSD rlogind
513-udp-who-BSD rwhod
514-tcp-shell-BSD rshd
514-udp-syslog-BSD syslogd
515-tcp udp-printer-Spooler. The print server LP1 service will listen on tcp port 515 for incoming connections
516-tcp udp-videotex-videotex
517-tcp udp-talk-" "Like tenex link- but across computers- BSD talkd" "
518-tcp udp-ntalk-talkd
519-tcp udp-utime-Unixtime
520-tcp-efs-Extended file name server
520-udp-route-Local routing process (on site); uses variant of Xerox NS routing information protocol;alias=router routed
521-tcp udp-ripng-ripng
522-tcp udp-ulp-User Location Service
523-tcp udp-ibm-db2-IBM-DB2
524-tcp udp-ncp-NCP
525-tcp udp-timed-Timeserver
526-tcp udp-tempo-Newdate
527-tcp udp-stx-Stock IXChange
528-tcp udp-custix-Customer IXChange
529-tcp udp-irc-serv-IRC-SERV
530-tcp udp-courier-RPC
531-tcp-conference-Chat
531-udp-rvd-control-MIT disk
531-tcp-irc-IRC
532-tcp udp-netnews-Readnews
533-tcp udp-netwall-For emergency broadcasts
534-tcp udp-mm-admin-MegaMedia Admin
535-tcp udp-iiop-iiop
536-tcp udp-opalis-rdv-opalis-rdv
537-tcp udp-nmsp-Networked Media Streaming Protocol
538-tcp udp-gdomap-gdomap
539-tcp udp-apertus-ldp-Apertus Technologies Load Determination
540-tcp udp-uucp-Uucpd
541-tcp udp-uucp-rlogin-uucp-rlogin
542-tcp udp-commerce-commerce
543-tcp udp-klogin-kerberos ( v4/v5 )
544-tcp udp-kshell-" "kerberos ( v4/v5 ) - Krcmd; alias=cmd" "
545-tcp-ekshal-kerberos encryptd remote shell -kfall
545-udp-appleqtsrvr-Apple Quick Time Server
546-tcp udp-dhcpv6-client-DHCPv6 Client
547-tcp udp-dhcpv6-server-DHCPv6 Server
548-tcp udp-afpovertcp-AFP over TCP
549-tcp udp-ifdp-IDFP
550-tcp udp-new-rwho-New-who
551-tcp udp-cybercash-cybercash
552-tcp udp-deviceshare-deviceshare
553-tcp udp-pirp-pirp
554-tcp udp-rtsp-Real Time Stream Control Protocol
555-tcp udp-dsf-" "phAse Zero(Stealth Spy) Trojan (Win 9x- NT) as well as dsf" "
556-tcp udp-remotefs-" "Rfs server; alias=rfs_server rfs- Brunhoff remote filesystem" "
557-tcp udp-openvms-sysipc-openvms-sysipc
558-tcp udp-sdnskmp-SDNSKMP
559-tcp udp-teedtap-TEEDTAP
560-tcp udp-rmonitor-Rmonitord
561-tcp udp-monitor-
562-tcp udp-chshell-Chcmd
563-tcp udp-nntps-nntp protocol over TLS/SSL (was snntp)
564-tcp udp-9pfs-Plan 9 file service
565-tcp udp-whoami-Whoami
566-tcp udp-streettalk-streettalk
567-tcp udp-banyan-rpc-banyan-rpc
568-tcp udp-ms-shuttle-Microsoft Shuttle
569-tcp udp-ms-rome-Microsoft Rome
570-tcp udp-meter-Demon
571-tcp udp-umeter-Udemon
572-tcp udp-sonar -sonar
573-tcp udp-banyan-vip-banyan-vip
574-tcp udp-ftp-agent-FTP Software Agent System
575-tcp udp-vemmi-VEMMI
576-tcp udp-ipcd-ipcd
577-tcp udp-vnas-vnas
578-tcp udp-ipdd-ipdd
579-tcp udp-decbsrv-decbsrv
580-tcp udp-sntp-heartbeat-SNTP HEARTBEAT
581-tcp udp-bdp-Bundle Discovery Protocol
582-tcp udp-scc-security-SCC Security
583-tcp udp-philips-vc-Philips Video-Conferencing
584-tcp udp-keyserver-Key Server
585-tcp udp-imap4-ssl-" "IMAP4+SSL (Use of 585 is not recommended- use 993 instead)" "
586-tcp udp-password-chg-Password Change
587-tcp udp-submission-Submission
588-tcp udp-cal-CAL
589-tcp udp-eyelink -EyeLink
590-tcp udp-tns-cml -TNS CML
591-tcp udp-http-alt-Filemaker - HTTP Alternative
592-tcp udp-eudora-set-Eudora Set
593-tcp udp-http-rpc-epmap-HTTP RPC Ep Map
594-tcp udp-tpip-TPIP
595-tcp udp-cab-protocol-CAB Protocol
596-tcp udp-smsd-SMSD
597-tcp udp-ptcnameservice-PTC Name Service
598-tcp udp-sco-websrvrmg3-SCO Web Server Manager 3
599-tcp udp-acp-Aeolon Core Protocol
600-tcp udp-ipcserver-Sun IPC server
606-tcp udp-urm-Cray Unified Resource Manager
607-tcp udp-nqs-Nqs
608-tcp udp-sift-uft-Sender-Initiated/Unsolicited File Transfer
609-tcp udp-npmp-trap-npmp-trap @microsoft.com
610-tcp udp-npmp-local-npmp-local @microsoft.com
611-tcp udp-npmp-gui-npmp-gui @microsoft.com
612-tcp udp-hmmp-ind-HMMP Indication @microsoft.com
613-tcp udp-hmmp-op -HMMP Operation@microsoft.com
614-tcp udp-sshell -SSLshell @quick.com.au
615-tcp udp-sco-inetmgr-Internet Configuration Manager
616-tcp udp-sco-sysmgr-SCO System Administration Server
617-tcp udp-sco-dtmgr-SCO Desktop Administration Server
618-tcp udp-dei-icda-DEI-ICDA @Quetico.tbaytel.net
619-tcp ydp-digital-evm-Digital EVM
620-tcp udp-sco-websrvrmgr-SCO WebServer Manager
621-tcp udp-escp-ip-ESCP @pobox.com
622-tcp udp-collaborator-Collaborator @opteamasoft.com
623-tcp udp-aux_bus_shunt-Aux Bus Shunt @ccm.jf.intel.com
624-tcp udp-cryptoadmin-Crypto Admin @cyberus.ca
625-tcp udp-dec_dlm-DEC DLM
626-tcp udp-asia-ASIA @apple.com
627-tcp udp-passgo-tivioli-CKS & TIVIOLI @ckshq.com
628-tcp udp-qmqp-Qmail Quick mail Queueing
629-tcp udp-3com-amp3-3Com AMP3
630-tcp udp-rda-RDA
631-tcp udp-ipp-IPP (Internet Printing Protocol)
632-tcp udp-bmpp-bmpp
633-tcp udp-servstat-Service Status update (Sterling Software)
634-tcp udp-ginad-ginad @eis.calstate.edu
635-tcp udp-rlzdbase-RLZ DBase @netcom.com
635-udp-mount-NFS mount Service
636-tcp udp-ldaps-ldap protocol over TLS/SSL (was sldap) @xcert.com
637-tcp udp-lanserver-lanserver @VNET.IBM.COM
638-tcp udp-mcns-sec-mcns-sec
639-tcp udp-msdp-MSDP
640-tcp udp-entrust-sps-entrust-sps
640-udp-pcnfs-PC-NFS DOS Authentication
641-tcp udp-repcmd-repcmd
642-tcp udp-esro-emsdp-ESPR-EMSDP V1.3
643-tcp udp-sanity-SANity
644-tcp udp-dwr-dwr
645-tcp udp-pssc-PSSC
646-tcp udp-ldp-LDP
647-tcp udp-dhcp-failover-DHCP Failover
648-tcp udp-rrp-Registry Registrar Protocol (RRP)
649-tcp udp-aminet-Aminet
650-tcp udp-obex-OBEX
650-udp-bwnfs-BW-NFS DOS Authentication
651-tcp udp-ieee-mms-IEEE MMS
652-tcp udp-udlr-dtcp-UDLR_DTCP
653-tcp udp-repscmd-RepCmd
654-tcp udp-aodv-AODV
655-tcp udp-tinc-TINC
656-tcp udp-spmp-SPMP
657-tcp udp-rmc-RMC
658-tcp udp-tenfold-TenFold
659-tcp udp-url-rendezous-URL Rendezous
660-tcp udp-mac-srvr-admin-MacOS Server Admin
661-tcp udp-hap-HAP
662-tcp udp-pftp-PFTP
663-tcp udp-purenoise-PureNoise
664-tcp udp-secure-aux-bus-Secure Aux Bus
665-tcp udp-sun-dr-Sun DR
666-tcp udp-mdqs
666-tcp udp-ftpattack-FTP Attack Trojan
666-tcp udp-satanz-Satanz Backdoor Trojan
666-tcp udp-doom-Doom Id Software
667-tcp udp-disclose-campaign contribution disclosures-SDR Technologies @lambda.com
668-tcp udp-mecomm-MeComm @esd1.esd.de
669-tcp udp-meregister-MeRegister
670-tcp udp-vacdsm-sws-VACDSM-SWS
671-tcp udp-vacdsm-app-VACDSM-APP
672-tcp udp-vpps-qua-VPPS-QUA
673-tcp udp-cimplex-CIMPLEX @cesi.com
674-tcp udp-acap-ACAP @innosoft.com
675-tcp udp-dctp-DCTP @ansa.co.uk
676-tcp udp-vpps-via-VPPS Via @cesi.com
677-tcp udp-vpp-Virtual Presense Protocol
678-tcp udp-ggf-ncp-GNU Gereration Foundation NCP
679-tcp udp-mrm-MRM
680-tcp udp-entrust-aaas-entrust-aas
681-tcp udp-entrust-aams-entrust-aams
682-tcp udp-xfr-XFR
683-tcp udp-corba-iiop-COBRA IIOP
684-tcp udp-corbra-iiop-ssl-COBRA IIOP SSL
685-tcp udp-mdc-portmapper-MDC Port Mapper
686-tcp udp-hcp-wismar-Hardware Control Protocol Wismar
687-tcp udp-asipregistry-AppleShare IP Registry
688-tcp udp-realm-rusd-REALM-RUSD
689-tcp udp-nmap-NMAP
690-tcp udp-vatp-VATP
691-tcp udp-msexch-routing-MS Exchange Routing
692-tcp udp-hyperwave-isp-Hyperwave-ISP
693-tcp udp-connendp-connendp
694-tcp udp-ha-cluster-ha-cluster
695-tcp udp-ieee-mms-ssl-IEEE-MMS-SSL
696-tcp udp-rushd-RUSHD
700-tcp udp-bphone-BuddyPhone Internet telephony as well as the TCP range 5000-5111
704-tcp udp-elcsd-Errlog copy/server daemon
705-tcp udp-agentx-AgentX for SNMP @acec.com
706-tcp udp--Unassigned
707-tcp udp-borland-dsj-Borland DSJ
708-tcp udp--Unassigned
709-tcp udp-entrust-kmsh-" "Entrust Key Management Service Handler- Nortel DES auth network see 389/tcp" "
710-tcp udp-entrust-ash-Entrust Administration Service Handler @entrust.com
711-tcp udp-cisco-tdp-Cisco TDP
712-728-tcp udp--Unassigned
729-tcp udp-netviewdm1-IBM NetView DM/6000 Server/Client
730-tcp udp-netviewdm2-IBM NetView DM/6000 send/tcp
731-tcp udp-netviewdm3-IBM NetView DM/6000 receive/tcp
740-tcp udp-netcp (old)-NETscout Control Protocol ( old )
741-tcp udp-netgw-NetGW
742-tcp udp-netrcs-Network based Rev. Cont. Sys.
744-tcp udp-flexlm-Flexible License Manager
747-tcp udp-fujitsu-dev-Fujitsu Device Control
748-tcp udp-ris-cm-Russell Info Sci Calendar Manager
749-tcp udp-kerberos-adm-Kerberos admin/changepw ( v5 )
750-udp-kerberos-iv-Kerberos authentication ( v4 ); alias=kdc
750-tcp udp-rfile-rfile
750-udp-loadav
751-tcp udp-kerberos-master-" "Kerberos " "" "kadmin" " ( v4 )" "
751-tcp udp-pump-pump
752-tcp udp-qrh-Kerberos password server
753-tcp udp-rrh-Kerberos userreg server
754-tcp-krb_prop-Kerberos/v5 server propagation
754-tcp udp-tell-Send
758-tcp udp-nlogin
759-tcp udp-con
760-udp-ns
760-tcp-krbupdate-" "kreg- kerberos/4 registration" "
761-udp-rxe-
761-tcp-kpasswd-" "kpwd- Kerberos/4 password" "
762-tcp udp-quotad
763-tcp udp-cycleserv
764-tcp udp-omserv
765-tcp udp-webster
767-tcp udp-phonebook-Phone
769-tcp udp-vid
770-tcp udp-cadlock
771-tcp udp-rtip
772-tcp udp-cycleserv2
773-tcp -submit
773-udp-notify
774-tcp-rpasswd
774-udp-acmaint_dbd
775-tcp -entomb
775-udp-acmaint_transd
776-tcp udp-wpages
777-tcp udp-multiling-http-Muiltiling HTTP
778-779-tcp udp--Unassigned
780-tcp udp-wpgs
781-tcp udp-hp-collector-HP performance data collector
782-tcp udp-hp-managed- node-HP performance data managed node
783-tcp udp-hp-alarm-mgr-HP performance data alarm manager
786-tcp udp-concert-concert
787-tcp udp-qsc-QSC
788-799---Unassigned
799-tcp-controlit
800-tcp udp-mdbs_daemon
801-tcp udp-device
802-809---Unassigned
810-tcp udp-fcp-udp-FCP Datagram
811-827---Unassigned
828-tcp udp-itm-mcell-s-itm-mcell-s
829-tcp udp-pkix-3-ca-ra-PKIX-3 CA/RA
830-870-tcp udp--Unassigned
871-tcp-supfilesrv-SUP server
872-tcp udp--Unassigned
873-tcp udp-rsync-rsync
874-885-tcp udp--Unassigned
886-tcp udp-iclcnet-locate-ICL coNETion locate service
887-tcp udp-iclcnet_svinfo-ICL coNETion server info
888-tcp udp-accessbuilder-AccessBuilder @3com.com
888-tcp-cddbp-CD Database Protocol @moonsoft.com
888-tcp -erlogin-Logon and environment passing
889-899-tcp udp--Unassigned
900-tcp udp-omginitialrefs-OMG Initial Refs @eng.sun.com
901-tcp udp-smpnameres-" "SMPNAMERES- Samba Swat- IIS RealSecure" "
902-tcp udp-ideafarm-chat-IDEAFARM-CHAT
903-tcp udp-ideafarm-catch-IDEAFARM-CATCH
904-910-tcp udp--Unassigned
911-tcp udp-xact-backup-xact-backup @xactlabs.com
912-988-tcp udp--Unassigned
989-tcp udp-ftps-data-" "FTP protocol- data- over TLS/SSL @consensus.com" "
990-tcp udp-ftps-" "FTP protocol- control- over TLS/SSL @consensus.com" "
991-tcp udp -nas-Netnews Administration System @fu-berlin.de
992-tcp udp-telnets-Telnet protocol over TLS/SSL @consensus.com
993-tcp udp-imaps-Imap4 protocol over TLS/SSL @consensus.com
994-tcp udp-ircs-irc protocol over TLS/SSL @consensus.com-
995-tcp udp-pop3s-pop3 protocol over TLS/SSL (was spop3) @microsoft.com
996-tcp udp-vsinet-vsinet
996-tcp udp-xtreelic-XTREE License Server
997-tcp udp-maitrd
998-tcp-busboy
998-udp-puparp
999-tcp -garcon
999-udp-applix ac-Applix ac
999-tcp udp-puprouter
1000-tcp-cadlock
1000-udp-ock
1000-1007-tcp udp--Unassigned
1001-tcp udp-silenser-Silencer Trojan
1001-tcp udp-WebEx-WebEx Trojan
1008-tcp udp-ufsd-UFS-aware server
1010-tcp udp-surf-surf
1011-tcp udp-doly-Doly Trojan
1012-udp-sometimes-rpcl-This is rstatd on a openBSD box
1022-1023-tcp udp--Reserved




56k.com modem information


56k.com has information on specific modems including a troubleshooting guide.




ACQUISITIONS | SALES AND MARKETING | TERMS AND CONDITIONS | ACCEPTABLE USE POLICY | SITE MAP | HOME

© 2004 Waymark Internet Services, Inc. All Rights Reserved.